Safe Work Australia data shows WHS penalties at a record high

WHS prosecutions fell to 308 in 2025, but Safe Work Australia's data shows the average penalty climbed to a record $147,985.

Robert Migliore
Director, Actevate
October 6, 2026
Last Updated
Read Time
5 min

Table of Contents

Upcoming Events

2025 at a glance

Safe Work Australia updates its WHS prosecutions dashboard each year, drawing on public reports of criminal prosecutions under WHS laws across every Australian jurisdiction since 1 January 2020. The 2025 figures were released in September 2026, and the three headline numbers below are the ones Safe Work Australia announced.

  • 308 WHS prosecutions in 2025, down from 321 in 2024.
  • $147,985 average financial penalty per prosecution, up 33% on 2024 and the highest annual average recorded.
  • 99% of prosecutions resulted in a financial penalty.

The fall in prosecutions is the first after four consecutive years of increases, which on its own reads as good news. The penalty figures tell a different story, because the average financial penalty is now the highest annual average recorded.

Chart: Most common industry divisions among defendants in 2025

  • Construction: 43%
  • Manufacturing: 20%
  • Mining: 6%
  • All other industries (calculated): 31%

The mix has shifted since last year. In the 2024 data the top three industries were construction, manufacturing, and transport, postal and warehousing. In 2025, mining has taken third place.

Note: Each defendant is recorded separately in the data, so a single incident can appear more than once. Safe Work Australia compiles the figures from publicly available information on regulators' websites.

Year-by-year trends

A small drop in case numbers says very little about your own exposure. The year-by-year figures on Safe Work Australia's dashboard show where enforcement has been heading since 2020. Unless stated otherwise, figures in this section and the next are read from the dashboard as at 6 October 2026.

Prosecution volumes

Trend: Number of prosecutions per year

  • 2020: 203
  • 2021: 273
  • 2022: 285
  • 2023: 309
  • 2024: 321
  • 2025: 308

Prosecutions rose for four consecutive years, from 203 in 2020 to 321 in 2024, an increase of 58%. The 2025 figure of 308 is the first fall in the data. It is 4% lower than the peak and still the third highest year.

Financial penalty rate

Trend: Share of prosecutions that resulted in a financial penalty

  • 2023: 97%
  • 2024: 98%
  • 2025: 99%

Despite the drop in cases, almost every prosecution recorded results in a financial penalty, and the share has edged up each year. These three figures are the ones Safe Work Australia reported in its September 2026 announcement. The dashboard only records prosecutions that resulted in a finding of guilt, so the figures show that a guilty outcome almost always comes with a financial penalty.

Total penalties

Trend: Total financial penalty per year

  • 2020: $26.67M
  • 2021: $27.77M
  • 2022: $32.29M
  • 2023: $40.34M
  • 2024: $34.95M
  • 2025: $44.99M

The total financial penalty for 2025 was $44.99 million. That is the highest annual total in the data and 29% more than in 2024, from 13 fewer prosecutions.

Average penalty

Trend: Average financial penalty per year

  • 2020: $136.76K
  • 2021: $104.02K
  • 2022: $117.86K
  • 2023: $134.9K
  • 2024: $111.65K
  • 2025: $146.54K

Note: The dashboard currently shows a 2025 average of $146.54K, slightly below the $147,985 that Safe Work Australia announced in September 2026 and that is quoted at the top of this article. On the dashboard figures, the 2025 average is about 31% higher than in 2024.

The average has moved up and down from year to year, with dips in 2021 and 2024. The 2025 figure is the first to pass the previous high set in 2020.

Fatal injury level

Trend: Number of prosecutions where the highest injury level was fatal

  • 2020: 42
  • 2021: 50
  • 2022: 46
  • 2023: 46
  • 2024: 50
  • 2025: 53

In 2025, 53 prosecutions were recorded with a highest injury level of fatal, the most in any year of the data. Prosecutions with a highest injury level of none have also grown, from 17% of the total in 2020 to 26% in 2025, after reaching about 30% in 2023 and 2024.

Note: These figures count prosecutions, not deaths. Each defendant is recorded separately, so one incident can appear more than once, and Safe Work Australia says the data should not be relied on to count the worker deaths or injuries prosecuted each year.

Info: Construction and manufacturing have remained the most common industry divisions among defendants since data collection began in 2020. If you operate in either sector, regulators already know where to look.

Six-year view

Combined, the six years of data say a lot about who is prosecuted and why.

  • 1,699 prosecutions recorded from 2020 to 2025.
  • $207M total financial penalty.
  • $125K average financial penalty from 2020 to 2025.

Highest injury level

Chart: Number of prosecutions by highest injury level, 2020 to 2025

  • Serious: 856
  • None: 426
  • Fatal: 287
  • Unknown: 76
  • Minor: 54

One in four of these prosecutions recorded a highest injury level of none. Safe Work Australia uses that label where there was no injury or other direct impact on a worker, for example where an inspection identified a failure but no injury was caused. A further 287 prosecutions, about 17% of the total, recorded a highest injury level of fatal.

Info: As a guide, Safe Work Australia treats an injury as serious where, for example, it requires hospitalisation for more than a day or results in a fracture of a major bone. Half of all recorded prosecutions had a highest injury level of serious.

Plea

Chart: Number of prosecutions by plea, 2020 to 2025

  • Guilty: 80.8%
  • Unknown: 17.2%
  • Not guilty (calculated): 2.1%

Four in five defendants pleaded guilty. The recorded share of guilty pleas has fallen from 93% in 2020 to 72% in 2025, but that mostly reflects more pleas being recorded as unknown, which rose from 4% to 27% over the same period. Not guilty pleas have stayed in single figures every year.

Category of main offence

Chart: Number of prosecutions by category of main offence, 2020 to 2025

  • Category 1: recklessly expose a person to risk of death or serious injury/illness: 39
  • Category 2: fail to comply exposes a person to risk of death or serious injury/illness: 730
  • Category 3: fail to comply: 52
  • Not applicable: 871
  • Unknown: 7

Very few offences sat at the most serious level. Only 39 prosecutions were Category 1 offences, where a duty holder recklessly or with gross negligence exposes a person to a risk of death or serious injury or illness. Ten of those were in 2025, the most in any year and double the number in 2024.

Where a category is recorded, about 95% of prosecutions were Category 2 or Category 3 offences, which involve a failure to comply with a health and safety duty, and Category 1 offences made up about 5%. Another 871 prosecutions are recorded as not applicable, which Safe Work Australia uses for jurisdictions that had not implemented the model WHS laws in the year of prosecution.

Industry of defendant

Construction has recorded the most prosecutions in every year of the data, with manufacturing second each time. Across the full six years, the dashboard lists transport, postal and warehousing third, ahead of electricity, gas, water and waste services and then agriculture, forestry and fishing.

Note: The dashboard only records prosecutions that resulted in a finding of guilt, and it relies on what each regulator publishes. Safe Work Australia cautions that the data is limited by what is publicly available and should not be relied on for research or other purposes.

Psychosocial risk outlook

The link to psychosocial risk comes from timing. Codes of practice have been legally binding in NSW since 1 July 2026, including the Managing Psychosocial Hazards at Work Code of Practice, so employers are now expected to show how they identify, assess, control and review psychosocial hazards on an ongoing basis.

At the same time, a tool many organisations leaned on has been switched off. People at Work, the free psychosocial risk assessment survey funded by Australian WHS regulators and used by more than 160,000 workers since 2020, closed to users on 2 October 2026.

Note: An organisation-wide survey score was never the whole picture. Psychosocial pressure tends to build in particular teams and under particular leaders, so the evidence that counts shows where a hazard sits and what was done about it.

Implications for officers and boards

Under WHS laws, officers have a personal duty to exercise due diligence. That duty is about more than receiving reports. It asks officers to understand the risks in their business and to verify that the controls for those risks are being used.

That distinction is important in a prosecution. A documented procedure shows what was meant to happen, while the evidence a court looks for is what happened on the day.

An average penalty of $147,985 that grew by about a third in a single year is also an enterprise risk. That puts WHS in front of the board and the audit committee, and it can no longer sit only with the people and culture team.

Questions worth asking at your next leadership meeting include:

  • Which of our risks could kill or seriously injure someone, and who owns each one?
  • When did we last check that the controls for those risks were working on site, and not only written down?
  • Do our board or executive reports show control effectiveness, or only incident counts?
  • How do concerns raised by workers and contractors reach the people who can act on them?
  • Can we name our psychosocial hazards in the terms the Code uses, such as high job demands and low job control?
  • Do we know which teams those hazards are concentrated in, beyond the organisation-wide average?
  • Could we show a regulator a record of identifying, controlling and reviewing each one?

Tip: SafeWork NSW has published a free officer due diligence self-assessment tool. It is a quick way to see which records a regulator would expect your leadership team to produce.

Recommended next step

October is National Safe Work Month, which makes it a natural time to put this data in front of your leadership team. Pick one critical risk, trace it from the risk register to the worksite, and see whether the control you rely on is in place and understood by the people doing the work.

That single exercise will tell you more about your due diligence position than a year of lagging indicators.

How Actevate can help

Actevate helps organisations manage risk across the entire employee lifecycle, from pre-employment through to injury management and return to work. If the data has raised questions about your own systems, call 1300 663 155 or get in touch.

Sources

Disclaimer

This article is general information only and does not constitute legal or health and safety advice. The data is sourced from Safe Work Australia's WHS prosecutions dashboard and related publications, as available on 6 October 2026. Safe Work Australia revises the data each year, so figures may change after publication. Percentages marked as calculated, year-on-year comparisons and the charts are Actevate's own analysis and presentation of that data. Safe Work Australia has not reviewed or endorsed this article. Please refer to the original sources before relying on any figure.

★Key takeaways

?Frequently asked questions

Actevate service overview graphic

Join 600+ leading Australian companies who trust us to prioritise employee wellbeing.

Get in touch
Not sure which service is right for you? Book a discovery call.
#returntowork
#compliance
#mentalhealth

Other resources you may like

Clinician checking a worker's ears before a workplace hearing test
November 10, 2026
•
5 min
The employer's guide to workplace hearing tests

What is an audiometric assessment?

An audiometric assessment is a hearing test that checks how well a worker hears sounds at different pitches and volumes.

The first test sets a baseline for that worker's hearing. Every monitoring test after it is compared against that baseline, so any change shows up early.

Under Australian WHS laws, a business must provide these tests for workers who frequently wear hearing protection because noise in their role exceeds the exposure standard of 85 dB(A) averaged over eight hours. The baseline is due within three months of starting the work, and monitoring tests at least every two years after that.

Regular testing picks up noise-induced hearing loss in its early stages, while there is still time to investigate the cause and strengthen noise controls before the damage becomes permanent.

Actevate offers audiometry screening with our pre-employment health assessments, so every new starter's hearing is on record.

What the test involves

The test is painless and done in a quiet space, either at a clinic or at the workplace. It usually starts with a short history of the worker's noise exposure at work and outside it, then an ear check for blockages, before the worker listens to tones through headphones.

Note: Tests must be carried out by a competent person with the training and experience to run the test and interpret the results, ideally someone who also understands workplace noise risk and the demands of the worker's role. Testing must follow AS/NZS 1269.4:2014, the Australian standard for auditory assessment.

Why hearing loss deserves a place on your risk register

Noise-induced hearing loss is the single greatest cause of permanent hearing loss in Australia, and it is also the most preventable. It builds slowly, often over years, and by the time a worker notices it the damage cannot be reversed.

  • 23,693 workers compensation claims were made for hearing loss in Australia between 2015 and 2020
  • 80% of those claims came from trades, labourers and machinery operators
  • Close to 30,000 hearing loss claims had been lodged since 2015 by 2023, most of them from long-term exposure to hazardous noise

Source: Safe Work Australia, Hazardous noise infographic; Safe Work Australia, Collaborating to prevent work-related hearing loss.

SafeWork NSW names manufacturing, construction and transport, logistics and warehousing among the sectors with the most hearing loss claims. If your workforce is in one of these industries, audiometric testing is very likely already part of your legal duty.

Which workers need testing

Not every worker in a noisy workplace needs a hearing test. The duty applies to workers who are frequently required to wear hearing protection to protect them from noise above the exposure standard.

Info: The exposure standard for noise is an eight-hour average of 85 dB(A), or a peak of 140 dB(C). As a rough guide, if you need to raise your voice to talk to someone one metre away, the noise level is likely to be hazardous.

Handing out earplugs does not by itself trigger the testing duty. The trigger is how often a worker relies on hearing protection because noise in their role exceeds the standard. A noise assessment is the most reliable way to confirm which roles that covers.

Tip: List every role where hearing protection is required by signage, a site rule or the standard way the job is done. That list is the starting point for your testing program and for your next noise assessment.

When tests are due

The timing is consistent across the states covered here:

  • A baseline test within three months of a worker starting the work that requires hearing protection
  • Monitoring tests at least every two years after that, and more often for workers with very high average exposure across a shift

When each test happens matters too. Monitoring tests are best done a few hours into a shift, so they can pick up any short-term change in hearing. Where a test finds a change, a retest after at least 16 hours away from noise shows whether that change is temporary or permanent.

NSW

NSW requires audiometric testing under section 58 of the Work Health and Safety Regulation 2025. Workers employed before 1 January 2024 had to be tested before 1 January 2026, so every existing worker in scope should now have a baseline on file.

Queensland

The requirement began on 29 July 2025. New workers need a baseline within three months, and workers who started before 29 July 2025 must be tested before 29 July 2027.

Victoria

Victoria's OHS Regulations require testing within three months, at least every two years, and at any time a health and safety representative reasonably requests it. If two or more tests within two years show a drop of 15 dB or more at 3000, 4000 or 6000 Hz, the employer must arrange a full audiological examination.

Note: If any NSW workers in scope have not yet had a baseline test, the deadline has passed. Booking those tests is the first priority.

Tip: Add audiometry to your pre-employment medical for any role that needs hearing protection. In NSW, a pre-employment medical that includes an audiometric test can count as the worker's baseline, and Queensland will accept a pre-employment test that meets its criteria.

Source: SafeWork NSW, Hearing test requirements for NSW workers; WorkSafe Queensland, Audiometric testing FAQs; WorkSafe Victoria, Protecting employees from exposure to noise.

What to do with the results

Workers receive their results straight after the test, with an explanation of what they mean. Small changes between tests are not always clinically significant, which is why the retest matters before anyone draws a conclusion.

  • Temporary threshold shift: the worker is retested on another day after at least 16 hours in quiet conditions
  • Permanent threshold shift: the worker should be referred to a doctor, and in NSW the shift must be reported to your workers compensation insurer
  • Tinnitus reported: treated the same way as a significant shift, with a review of noise controls

Reviewing your noise controls

A significant shift is a sign that noise controls may not be working for that worker or that task. SafeWork NSW expects businesses to look first at higher-order controls, such as isolating or engineering out the noise source, before relying on hearing protection. The review should also cover:

  • Tasks that may have increased the worker's noise exposure
  • Whether the hearing protectors suit the noise level
  • How workers are trained to fit them, and whether they wear them for the whole shift
  • Ototoxic chemicals, such as some solvents, that can damage hearing and could be substituted

If a worker's hearing loss affects their ability to work safely, you need to take reasonably practicable steps to support them. That might mean visual warnings alongside audible alarms, adjusted equipment volume or alternative duties.

Tip: When one worker shows a shift, check the hearing protection fit and controls for everyone doing the same task. A shift in one person is often the first sign of a gap that affects the whole team.

Records, cost and labour hire

  • Cost: the employer organises and pays for every test, and workers don't need a doctor's referral
  • Records: all test reports, including updated baselines, must be kept confidential, and workers must be given a copy of their reports when their employment ends
  • Labour hire: the labour hire business is responsible for arranging and paying for testing, as it knows the worker's full noise exposure history, though the host business can pay instead if both agree

Note: In NSW, hearing test reports are health records, so they are covered by the Health Records and Information Privacy Act and the State Records Act. Store them with your other medical-in-confidence records, not on a personnel file.

My take: hearing test data is your best measure of noise risk

Most of my work in injury management starts after the damage is done. Noise-induced hearing loss is one of the few conditions where you can see the injury coming years in advance, but only if you are measuring it.

That is why I encourage employers to treat audiometric results as risk data, not a compliance record. A baseline captures the hearing a worker had on day one with your business. Without it, there is no reference point when a change shows up years later, and no way to separate what happened on your watch from what came before.

Monitoring results then tell you whether your controls are protecting people in practice. Looking across a team, the pattern matters more than any single test:

  • Stable results across a team are evidence your noise management is working
  • Small shifts clustered in one role or site usually point to a specific task, a piece of plant or hearing protection that isn't fitting properly

Read this way, a two-yearly test becomes an early warning system that lets you fix the gap long before it turns into permanent hearing loss and a claim.

How Actevate can help

Actevate offers professional audiometry screening as an add-on to our pre-employment health assessments, so new starters have their baseline on record from day one. We also deliver legislated medicals and health monitoring, and our return to work services support workers when an injury or condition affects their role. To set up hearing tests for your team, call 1300 663 155 or get in touch.

Sources

Disclaimer

This article is general information only and does not constitute legal or health and safety advice. Audiometric testing requirements differ between states and territories and may change, so check the current requirements with your WHS regulator and seek advice on your specific situation before acting.

All
#compliance
Actevate rehabilitation consultant meeting with an injured worker and employer
November 10, 2026
•
5 min
How much can one workers compensation claim cost your business?

Why one claim follows you for three years

If your average performance premium (APP) is over $30,000, icare classes you as an experience-rated employer, and your claims history directly changes what you pay. Employers under that threshold are small employers, and their premium is not directly affected by claims costs.

At each renewal, icare divides your premium-impacting claims costs for the previous three years by your APP for the same three years. That figure, your Claims Performance Measure, is then compared with a scheme-wide benchmark to decide whether your premium gets a loading or a discount.

Note: Because the calculation draws on three years of history, a claim lodged this year can influence your premium at each of your next three renewals, not just the next one.

Source: icare, Premium calculation for experience-rated employers; SIRA, Premium calculation.

What a loading looks like on a renewal

icare's own sample renewal pack shows how quickly claims costs add up. The sample employer's premium-impacting claims costs over three years came to 10% of its APP, against a scheme benchmark of 4.3%. That put its Claims Performance Rate at 232.56%, and its premium was adjusted by a factor of 1.605, around 60% above its average performance premium.

icare's worked example of an employer with no claims experience shows the opposite effect, with a 7.5% discount taking a $99,200 APP down to $91,760.

Chart: Premium adjustment by claims performance, icare examples

  • No claims experience: 7.5% below APP
  • Claims costs 2.3 times the scheme benchmark: around 60% above APP

Source: icare, Renewal premium information pack; icare, Premium calculation for experience-rated employers. The 60% figure is Actevate's calculation from icare's adjustment factor.

Info: Not every dollar spent on a claim counts towards your premium. Costs that do count include weekly compensation, permanent impairment and commutation payments.

Note: icare caps how far an experience-rated employer's premium rate can move in a single year, so a large loading can be spread across more than one renewal.

Why a psychological injury claim weighs so much more

  • 34.8 weeks median time off work for a mental health claim, compared with 7.0 weeks for other serious claims
  • $68,600 median compensation paid, compared with $16,100 for other serious claims
  • 17,900 serious mental health claims in 2024-25, or 12.2% of all serious claims
  • 169% increase in these claims since 2014-15

Source: Safe Work Australia, Key Work Health and Safety Statistics Australia 2026. Time lost and compensation are for 2023-24, the most recent finalised year.

Weekly compensation is one of the costs that feeds the premium calculation, so a claim with almost five times the time off carries far more weight in your Claims Performance Measure. At the national medians, a single mental health claim attracts more compensation than four other serious claims combined.

For an experience-rated employer with a clean record, that single claim can be the difference between a discount and a loading for three renewals in a row.

Tip: Ask icare for your cost of claims report and check which open claims are still paying weekly compensation. Those are the claims that will shape your next three renewals, and the ones where return to work support has the most value.

The hazard that rarely gets attention: organisational justice

Safe Work Australia defines poor organisational justice as a lack of procedural justice, such as fair decision-making processes, or of informational fairness, such as keeping everyone up to date and in the loop. It becomes a hazard when it is severe, prolonged or frequent, and it sits in the Managing Psychosocial Hazards at Work Code of Practice alongside better-known hazards like job demands and low job control.

The research linking fairness at work to absence is strong. A prospective study of 3,773 hospital employees in Finland found that low justice in decision-making procedures was associated with a 41% higher risk of sickness absence in men, and found no evidence that the link ran the other way, from poor health to perceptions of unfairness. A 2022 narrative review of 103 studies found the evidence that perceptions of workplace justice predict mental health and lower sickness absence to be relatively compelling.

Source: Safe Work Australia, Poor organisational justice; Kivimäki et al., Organisational justice and health of employees: prospective cohort study, Occupational and Environmental Medicine; Narrative review of organisational justice and health, 2022.

Where it shows up in claims

Harassment or workplace bullying caused 31.6% of serious mental stress claims in 2024-25, and work pressure caused 26.5%. In our experience, how fairly a bullying complaint is investigated and how workloads are shared out are often what decides whether a conflict stays a workplace issue or becomes a claim.

Safe Work Australia also notes that hazards combine. Poor organisational justice can create a higher risk in workplaces with low role clarity, where it isn't clear who should be making decisions.

Tip: Look for the early signs Safe Work Australia lists, such as gossip about decisions, unresolved issues or divisions among workers. Then check whether rosters and complaint outcomes are decided consistently, and whether workers are told how those decisions are made.

Protecting your premium starts before a claim

The three-year window works in both directions. Every renewal without a premium-impacting claim moves an older claim out of the calculation, and every claim kept short limits how much it adds.

  • Check which past claims drop out of the calculation at your next renewal, so you can forecast your premium rather than be surprised by it.
  • Act in the first weeks of a claim, because fewer than half of claimants are back at work within four weeks and another 22.7% return between week 4 and week 13. Early contact and suitable duties in that window keep a claim from becoming a long one.
  • Put organisational justice on your risk register with a control and a review date, the same as any other psychosocial hazard, rather than leaving it as an HR matter.

Source: Safe Work Australia, Key Work Health and Safety Statistics Australia 2026, return to work insights from workers compensation data.

Note: This article explains the NSW scheme run by icare. Victoria, Queensland and the other states use their own premium formulas, though most also factor in claims history for larger employers.

How Actevate can help

Actevate supports employers across the whole employee lifecycle. Our pre-employment health assessments match workers to the demands of their role, our return to work services help injured workers recover and return sooner, and our mental health training and Employee Assistance Program help you manage psychosocial risk before it becomes a claim. To talk through your claims history and what it means for your premium, call 1300 663 155 or get in touch.

Sources

Disclaimer

This article is general information only and does not constitute legal, insurance or health and safety advice. Premium calculations depend on your policy, industry classification and claims history, so speak to your insurer about your own premium. icare examples are illustrative and may not reflect current rates. Figures marked as calculated are Actevate's own analysis. icare and Safe Work Australia have not reviewed or endorsed this article.

All
#compliance
#mentalhealth
Tired manager rubbing his face in front of a laptop at his desk
November 3, 2026
•
5 min
How to spot and manage workplace fatigue under the new NSW Code

What the Code of Practice means by fatigue

The Code of Practice describes fatigue as a state of physical, mental or emotional impairment. It is more than tiredness. Fatigue can be short term or long term, and it builds when demands stay high without recovery.

Note: In NSW, fatigue is addressed under role overload and workload management in the psychosocial framework. It now also has its own approved Code of Practice, covered below.

What the numbers show and what NSW now expects

  • 12.4% of Australian workers work 50 or more hours a week, and some work more than 80
  • 46% of workers in mining work more than 50 hours a week, the highest of any industry
  • Workers with long hours are more likely to face other psychosocial hazards, such as role overload and emotional demands

Source: Safe Work Australia, fatigue infographic, using ABS Census 2021 and People at Work survey data.

Fatigue is also a safety risk. It reduces alertness, slows reaction times and impairs judgement. The risk is highest for workers who drive, operate machinery or do safety-critical tasks, and it includes the drive home after a long shift.

In February 2026, NSW approved a dedicated Code of Practice, Managing the risk of fatigue at work, based on Safe Work Australia's national model Code. Under section 26A of the WHS Act, which took effect in NSW on 1 July 2026, a business must manage the risks covered by an approved code to a standard equal to or higher than the code.

In our recent technical briefing on the new NSW psychosocial risk laws (watch the replay here), workplace lawyer James Mattson said businesses now need to go through approved codes "with a fine tooth comb", and he named fatigue alongside psychosocial hazards.

Info: The right to disconnect now applies to all national system employees. It began in August 2024 for businesses with 15 or more employees and on 26 August 2025 for small businesses. Employees can refuse to monitor, read or respond to out-of-hours contact unless the refusal is unreasonable.

What fatigue looks like

Fatigued workers may be yawning, making mistakes, or appearing irritable or forgetful.

Signs and symptoms to look out for

  • Trouble concentrating or making decisions
  • Poor memory and slower reactions
  • Low motivation and less interest in work they used to enjoy
  • Headaches, dizziness, blurred vision and more frequent illness
  • Arriving late or more unplanned absences

Common causes

  • Long overtime hours, on-call duties and too few breaks
  • Poor sleep and ongoing work stress
  • Time pressure and a lack of resources to do the job
  • Blurred boundaries between work and home
  • Shift work without recovery time, including consecutive night shifts
  • Intense, sustained focus without a pause
  • High mental, physical or emotional demands, and other psychosocial hazards
  • Environmental conditions such as extreme temperatures, poor lighting and vibration

Who is most at risk

  • Shift and night workers
  • Emergency services and frontline health workers
  • Workers on long rosters, overtime or on-call duties
  • Workers with long commutes, especially after a shift

Fatigue, stress and burnout

Some pressure at work is normal. The risk comes from high demands without enough recovery time. Over time, this leads to fatigue and burnout.

Psychologist Kelly Hunt, who presented at our technical briefing, drew the link to workload directly: "It's the constant and excessive high workload that will then lead to fatigue, which is another one under this code."

Early warning signs of fatigue in your team

Kelly's case study showed how fatigue can build without anyone noticing. Kevin, a long-serving manager, "used to have a great work-life balance", but under sustained stress he couldn't sleep and would "work all through the night" to show his managers he was trying. The emails he sent at three or four o'clock in the morning were one of the clearest signs.

Behaviour change

  • Emails or messages sent late at night or very early in the morning
  • Mistakes, missed deadlines or disorganisation from someone who was previously reliable
  • Irritability, forgetfulness or withdrawal from the team

Organisational data

  • Overtime hours and timesheets that keep climbing
  • Leave balances building up because people aren't taking time off
  • Rising sick leave, absenteeism, near misses and incidents

Tip: Kelly's advice is to respond directly when you see after-hours emails. Ask, "What's going on? Why do you feel the need to send an email at 3 o'clock in the morning?" Then monitor whether it becomes an ongoing pattern.

Practical ways to manage fatigue

Review rosters and hours

Ensure adequate rest between shifts, limit excessive overtime, and rotate demanding tasks to give recovery time. SafeWork NSW also recommends reviewing rosters, timesheets, near misses and incident reports with your workers, and avoiding pay or other incentives that reward excessive hours.

Design safer schedules

Avoid back-to-back night shifts or very long shifts, and use job rotation so the same person isn't always doing the most tiring tasks. Where night work is needed, use forward-rotating shifts, keep complex and safety-critical tasks away from likely fatigue periods, and allow recovery time after a run of night shifts.

Note: The NSW fatigue Code says caffeine and other stimulants should not be relied on as a control. Workplace napping can support other controls, but it should not be the only one.

Promote recovery

Encourage micro-breaks (brief pauses to rest eyes or stretch), and make sure team members take their leave and time off to recharge. When leaders model the right to disconnect, staff feel able to follow it.

Workers can support their own recovery too. A consistent sleep routine, time away from screens before bed and regular movement during the day all help.

Consult and write it down

Talk with workers about the hazards that lead to fatigue before rosters are finalised. A fatigue policy is not mandatory, but SafeWork NSW recommends developing one with your workers. It should cover responsibilities, excessive hours, fitness for work and how to report fatigue.

Tip: Ask your managers one question this week: on average, how many extra hours are people in your teams working each week?

A five-minute fatigue check for managers

Run through these questions for your team:

  • Has anyone worked long or back-to-back shifts this month without a proper recovery break?
  • Are the same people always covering nights, call-outs or the most demanding tasks?
  • Is anyone sending emails or messages well outside their normal hours?
  • When did each person last take annual leave?

An uncomfortable answer to any of these is a reason to review that roster and talk with the person, not a reason to wait for the next incident.

How Actevate can help

Our mental health training helps managers recognise early warning signs and handle the conversations that follow, and our Employee Assistance Program gives your people access to qualified clinicians who understand your business.

If you would like to talk through fatigue or other psychosocial risks in your workplace, request a callback and our team will be in touch to book a time to meet.

Sources

Disclaimer

This article is general information only and does not constitute legal or professional advice. Obtain independent advice specific to your organisation before acting on any information presented.

All
#mentalhealth